BEST SELLING PRODUCTS
The Mynics IR Sensor is a general purpose proximity sensor, which is usually used for obstacle detection. The sensing range is higher than most other modules. The module consists of an IR emitter and IR receiver pair and also an LM 358 comparator IC. The on-board LED indicator helps check the status of the sensor without using any additional hardware. The power consumption of this module is low and gives a digital/analog output.
Arduino Uno R3 Compatible – Atmega 328 DIP
This is the Arduino Uno R3. In addition to all the features of the previous board, the Uno now uses an ATmega16U2 instead of the 8U2 found on the Uno (or the FTDI found on previous generations). This allows for faster transfer rates and more memory. No drivers needed for Linux or Mac (inf file for Windows is needed and included in the Arduino IDE), and the ability to have the Uno show up as a keyboard, mouse, joystick, etc.
7 Segment Display Module TM1637
A useful data output for your Arduino project might be a simple 4-digit display. These displays make use of the TM1637 chip.
Servo Motor SG-90
SG90 is the most popular 9g servo in the world, SG90 digital servo is the new version of SG90 anaglo servo.
Power Supply Adaptor for Raspberry Pi/Arduino/GSM & GPS Modules₹300.00
Bluetooth Module HC-05
HC‐05 module is an easy to use Bluetooth SPP (Serial Port Protocol) module,designed for transparent wireless serial connection setup.The HC-05 Bluetooth Module can be used in a Master or Slave configuration, making it a great solution for wireless communication.
Arduino Compatible Nano V4
The Arduino Nano V4 is a small, complete, and breadboard-friendly board based on the ATmega328. It differs from our other Nano V3 board in using a Prolific PL2303 chipset instead of the FTDI chip in the Nano V3.
Relay Module 5V 4CH
The 5V 4-Channel Relay interface board can control various appliances, and other equipment with large current. It can be controlled directly by Micro-controller (Raspberry Pi, Arduino , 8051, AVR, PIC, DSP, ARM, ARM, MSP430, TTL logic) .
L293D-Arduino Uno Shield-For Stepper,Servo and DC Motors
The shield contains two L293D motor drivers and one 74HC595 shift register. The shift register expands 3 pins of the Arduino to 8 pins to control the direction for the motor drivers. The output enable of the L293D is directly connected to PWM outputs of the Arduino.
Button Cell LR41
These are generally used to power small toys, clocks, LEDs, watches, calculators etc.. High quality & stable 1.5v Alkaline batteries.
Specifications:Model : LR41 (AG3, LR41, 192, 392A, SR41, LR736, CX41, 392)Cell Type: Button cellNominal Voltage : (V) 1.5Nominal Capacity : (mAh)* 28External Diameter : 7.9 mmExternal Height : 3.6 mmOperating Temperature Range : (deg. C): –20 to +85
These round high capacity cells have been mainly used in flashlight type applications but with its capability to be used as a drop-in rechargable cell at 3.7V with a capacity of 2600mAh. This is a great battery option for those of you who need a simple-to-install and replace cell with a lot of juice.
These 18650 Cells have a standard discharge current of 0.2C to a maximum of 1C and can handle about 300 charge cycles.
- Max. Output Voltage : 12V
- Max. Output Current : 150mA
- Dimensions : 115x115x2mm
Mynics L293D Motor Driver Board
The Mynics L293D Motor Driver Board comes with the popular motor driver IC L293D, designed to provide bidirectional drive currents of up to 600-mA at voltages from 4.5 V to 25 V. It has Terminal Blocks for connecting motors & the power supply, along with Berg Sticks for control signals from a micro controller. This can control 2 DC Motors with their direction, using control lines and their speed, using PWM. It can easily be connected with an Arduino or Raspberry Pi. What it really does is that it boosts the 5V signal from your controller to 12V, to run a motor.
Nylon Screw and Stand-off Set – M3 Thread – 180 pcs
This M3 Screw Set has 180 pieces, to help you build your DIY projects. The M3 size screws, fit almost all breakout and development board mounting holes. Since they are nylon you can file them down easily, and they don’t conduct electricity or interfere with antennas or magnetometers.
Wi-Fi Module ESP-8266-07
The ESP8266 WiFi Module is a self contained SOC with integrated TCP/IP protocol stack that can give any microcontroller access to your WiFi network. The ESP8266 is capable of either hosting an application or offloading all Wi-Fi networking functions from another application processor. Each ESP8266 module comes pre-programmed with an AT command set firmware, meaning, you can simply hook this up to your Arduino device and get about as much WiFi-ability as a WiFi Shield offers.